Arena do Vidro

Home › Blog

Published on 11/05/2026 · by Leandro Caldas, glazier, founder of Routeck and creator of the Arena

Gap between mirror and metal frame: welding pulls the metal

Apply

The gap between mirror and metal frame is a detail almost nobody thinks about until the mirror won't fit. That's what happened in the Arena do Vidro final. With the clock running, one of the finalists cut the mirror to the exact size of the frame, welded it, and the weld pulled the metal. The mirror that was supposed to fit no longer did.

This moment is in episode 4, in the video above. I like it because it's the mistake of someone who knows what he's doing: the theory was in his head, the rush just kept him from applying it. And it's the kind of mistake that costs money in any shop, not just in a 60-minute challenge.

Arena do Vidro finalist measuring the metal frame with a tape on the floor
The frame on the floor, measured with a tape: this is where the gap math comes in.

What happened in the challenge

The explanation came right away from someone watching: he made it too tight, left no room for an allowance, and when he welded, it pulled. As it stood, the mirror wouldn't go in, and it was so tight it risked cracking.

The finalist admitted it plainly: he knows welding pulls. He cut the mirror to the exact size when he could have left a few extra millimeters for some play. The bill came twice over: he had to cut the metal tube again, weld again and also trim the mirror.

Gap between mirror and metal frame: welding pulls the metal

Why welding pulls the metal

When metal heats up during welding, it expands. When it cools, it shrinks, and the weld bead pulls the pieces with it. The result is a frame that ends up a little smaller or a little crooked compared to what you measured before welding. On a metal part that sometimes doesn't even show. With a mirror inside it shows right away, because glass doesn't give.

And it's not only about size. Even if the mirror fits, if it's tight against the metal, any twist in the frame becomes pressure on the edge of the glass. That was the cracking risk pointed out during the challenge.

Finalist welding the metal frame on the floor during the Arena do Vidro final
Welding on the floor: every point of heat changes the size a little.

How to plan the gap between mirror and metal frame

  • Weld first and cut the mirror afterward, measuring the finished, cooled frame.
  • If the mirror has to be cut first, build the gap into the design: in the challenge, a few millimeters were missing.
  • Measure the frame in more than one spot. After welding, the two sides may not match.
  • Check that it's square before the glass gets near it.
  • Don't force the mirror. If it doesn't slide in loose, the frame or the piece has to change.

The turnaround: weld on the outside and cut what's left

The most interesting part comes after the mistake. With time running, the strategy changed: he took about 2 centimeters off the mirror, resized it and switched to welding on the outside, cutting whatever was left over. The reaction from those watching was that it was a good idea, because he wouldn't keep losing time there.

In a challenge or in the shop, the lesson is the same: when the plan breaks, there's no use insisting. Stop, fix what you can and move on. The commentary also noted another factor in the frame: flat bar fools you, because it bends easily but it's floppy. That topic has its own post.

Pressure changes everything

The line that sticks is the finalist's own: he already had the idea in his head, but when it was time to execute, the adrenaline wouldn't let him. That's why it's worth making the gap a written rule in your shop, instead of trusting you'll remember on a busy day.

How much gap should I leave between the mirror and the metal frame?
In the challenge, the finalist said he could have left a few more millimeters. The safest way is to measure the finished, cooled frame and cut the mirror to that size.
Why does the frame change size after welding?
Because the metal heats up, expands and, as it cools, shrinks and pulls the pieces along with the weld bead.
Can the mirror crack if it's tight in the frame?
Yes. That was the risk pointed out in the final: it was so tight it could have cracked.

Want to talk about metal frames? Message me on WhatsApp at +55 31 9095-8383.

Full episode 4 · MIG welding a mirror frame · How to plan a framed mirror before cutting metal

Apply

Want to challenge the champion and win R$ 10,000?

Want to be on the next season? Fill in your details: the production team contacts selected glaziers on WhatsApp.

Your details are used only by the Arena do Vidro production team to contact you.

Episode 4

Apply