Arena do Vidro

Home › Blog

Published on 11/16/2026 · by Leandro Caldas, glazier, founder of Routeck and creator of the Arena

Cactus mirror: the same machine that cut the Arena Hello Kitty

Apply

The cactus mirror in this post's video is all curves: arms going out, curves going in, rounded tips. It is the kind of shape that, by hand, makes a glazier lose the piece on the very last stretch. It was cut on the Router Glass, the same machine that had the Hello Kitty mirror ready for the first episode of Arena do Vidro.

Putting the two cases side by side shows something the show made clear: the machine solves the cut, but the mirror only turns out well when the rest of the work keeps up. Here is what each one showed.

Router Glass cutting a mirror on the table, with the printed part label next to it
The same Router Glass that cut the Arena Hello Kitty.

In the Arena, the cut was the one thing nobody argued about

On EP1, Janael and Rômulo had 1 hour and 30 minutes to copy a Hello Kitty shaped mirror with a sandblasted band, LED and a touch button. The mirror arrived already cut: Isaac cut it on the Router Glass before the challenge. The machine also cuts the sandblast vinyl with its laser, but the rule that day was to cut the vinyl by hand.

At the judging table, nobody went easy. One judge said the only thing that looked like the model was the cut, and that the contestant had not made it, the machine had. The sandblast outline, the width of the band and the finish all came out different from the model. The cut did not.

Cactus mirror on the mirror cutting machine: from cut to finish

On the cactus mirror, the machine cuts the same drawing twice

The cactus video shows something the Hello Kitty challenge did not: the same machine cutting the MDF backing and then the mirror, in the same shape. Besides the mirror cutter, the Router Glass has a 530 W router spindle that works MDF, acrylic and ACM. There is a single drawing, made in Corte Glass, the software that ships with the machine, so the backing and the mirror come out in the same shape.

On the Hello Kitty, one of the steps that slowed the contestants down most was exactly the one the machine could do and the rules banned: cutting the vinyl. At his own shop, Rômulo uses templates he makes himself for tight curves. Without them, he improvised one on the spot to get the bow done. The judges praised the fix. In everyday work, that time is what the machine's 10 W laser saves.

What is still the glazier's job, cactus or Hello Kitty

  • Breaking out. The machine scores and puts the breakout lines in the right place, but your hands free the pieces.
  • Edging the inside curve. On EP1, the edger chattered on the inner curve and Rômulo thought the mirror would break. Vinícius told him to lower the machine's speed and change its angle, and that saved the piece.
  • Finishing. The cactus in the video still goes through finishing after the cut. On the Hello Kitty, the judges criticized the sandblasting and the finish, not the outline.
  • Knowing what the customer asked for. A shape full of curves is only worth it if the rest of the piece lives up to the cut.

From EP3 to the cactus: one minute against twenty

On EP3, the challenge was to cut by hand, in 20 minutes, a curved shape identical to the template, without laying the template on the mirror. The judges called it a tie: one mirror cracked during breakout, and the other came out with the drawing mirrored the wrong way. In the middle of the challenge I said that on the Router Glass I would cut that shape in about one minute, by myself.

The cactus is the proof of that outside the arena: a shape full of curves, cut with the ±0.5 mm precision listed on the machine's spec sheet. What the show teaches is not to confuse a good cut with a finished mirror. The machine delivers the same cut every time. The rest is still craft.

Was the cactus mirror cut on the same machine used in Arena do Vidro?
Yes. The cactus in the video and the Hello Kitty mirror from EP1 were both cut on the Router Glass.
Does the Router Glass also cut the MDF backing?
Yes. Besides the mirror cutter, it has a 530 W router spindle for MDF, acrylic and ACM, and a 10 W laser to cut sandblast vinyl.
Why was the vinyl cut by hand in the Arena?
It was the rule of the EP1 challenge. The machine cuts it with the laser, but the challenge required a manual cut, and it was one of the steps where the contestants struggled most.

Want to know how we would cut a shape like this for your order? Message me on WhatsApp at +55 31 9095-8383. The machine's spec sheet is at routeck.com.br/en/machines/router-glass. And if you cut curves by hand without fear, sign-ups for the next season of the Arena are open on this site.

Episode 1: the Hello Kitty mirror · How to edge a curved mirror without breaking it · Organic mirror: what the Arena showed

Apply

Want to challenge the champion and win R$ 10,000?

Want to be on the next season? Fill in your details: the production team contacts selected glaziers on WhatsApp.

Your details are used only by the Arena do Vidro production team to contact you.

Apply