Arena do Vidro

Home › Blog

Published on 11/06/2026 · by Leandro Caldas, glazier, founder of Routeck and creator of the Arena

Why trimming too little glass leaves a jagged mirror edge

Apply

Trimming too little glass leaves a jagged edge. Every glazier has seen it: you need to take a few millimeters off a mirror, you score it, and the strip that should come off breaks into bits and leaves a serrated edge. It happened again in the Arena do Vidro final, and in the same stretch there was another lesson worth just as much: show up with the plan ready for whoever is going to weld.

These look like two separate topics, but it is the same idea: what you decide before you pick up the tool is what makes the piece come out fast and clean, or turn into rework.

MIG welding the metal mirror frame during the Arena do Vidro final
The frame being welded on the floor, with the design already settled.

A plan ready for the welder

The final challenge was a mirror with a metal frame that could stand on its own, in 60 minutes. Welding was not everyone's strength, and each finalist could call in help. Janael called Rui, who has been welding for 10 years. Rui said it right there: Janael had everything prepared and left only one way to weld it. In about 10 minutes, he had the mirror frames practically done.

Janael explained the strategy: from the start he planned knowing he would need someone, because welding was his weak spot. He set it up for that, and Rui built exactly what he had in mind. The help was fast because the hard part, deciding the design, was already done.

Arena do Vidro finalist explaining how he planned the frame before calling the welder
Plan first: the welder only had to execute.

What this means in a glass shop

It works the same way in a glass shop. When you hand off the frame, the cutting or the install, the person doing it works much faster if the piece is already decided: size, shape, where the welds go, how the mirror fits. If the metalworker has to guess, he loses time, and you risk getting something different from what you pictured.

  • Settle the design and measurements before calling for help.
  • Make it clear where each weld goes and how the mirror fits in the frame.
  • Separate your part (the glass) from theirs (the metal) and hand theirs over ready to build.
  • Remember welding pulls the metal: measure the mirror from the finished frame.

Why trimming too little glass leaves a jagged edge

In the same stretch, a finalist had to make the mirror smaller and the strip that had to come off was too thin. It left a row of teeth, and he went to the grozing pliers and then to sandpaper. The comment at the bench was blunt: he needed to take off half a centimeter. Every time you take off too little, that happens. Take more: leave at least about half a centimeter.

The reason comes from the bench: a score only runs clean when the piece coming off has enough body to lever against. A strip a few millimeters wide has nothing to grip, it breaks into bits and the crack wanders off the score. I covered this in detail in the post about glass grozing pliers.

Flat bar instead of square tube

There was also a change of plan I only caught in the moment: I thought one of the finalists would use square tube, and he ended up building the frame with just the flat bar. In the final, each one picked a path, and the result showed what each choice cost.

Why does glass chip into teeth when I trim a thin strip?
Because a thin strip has no body to lever against. It breaks into pieces and the crack leaves the score line, so the edge comes out serrated.
How much glass should I leave to trim off?
At the bench in the final the advice was at least half a centimeter. If you need to take off less, re-score with more margin.
How do I speed up a metal frame when someone else welds it?
Hand over a settled plan: design, measurements and where each weld goes. In the final, that let the welder build the frames in about 10 minutes.

Want to talk mirror cutting and frames? Message me on WhatsApp at +55 31 9095-8383. And if you want to show your method at the bench, sign-ups for the next Arena season are open here on the site.

Full episode 4 · Glass grozing pliers: why thin strips leave teeth · Gap between mirror and metal frame · Flat bar vs square tube for a mirror frame

Apply

Want to challenge the champion and win R$ 10,000?

Want to be on the next season? Fill in your details: the production team contacts selected glaziers on WhatsApp.

Your details are used only by the Arena do Vidro production team to contact you.

Episode 4

Apply